...
Parameter Name | Function |
|---|---|
#<_motion_mode> | Returns the G value multiplied by 10 of G1/G2/G3/G5.2/G73/G80/G82/G83/G86/G87/G88/G89 (eg, G83 equals 830) |
#<_plane> | Returns the G value multiplied by 10 of G17/G18/G19/G17.1/G18.1/G19.1 (eg, G18.1 equals 181) |
#<_ccomp> | Returns the G value multiplied by 10 of G40/G41/G42 (eg, G40 equals 400) |
#<_ccomp_diameter> | Returns the diameter applied by cutter compensation, equivalent to parameter #5410 |
#<_metric> | Returns 1 if G21 is on |
#<_imperial> | Returns 1 if G20 is on |
#<_absolute> | Returns 1 if G90 is on |
#<_incremental> | Returns 1 if G91 is on |
#<_inverse_time> | Returns 1 if G93 is on |
#<_units_per_minute> | Returns 1 if G94 is on |
#<_units_per_rev> | Returns 1 if G95 is on |
#<_work_offset_number> | Returns 1-500 for the currently active work offset equivalent to G54.1 P# |
#<_tool_offset> | Returns 1 if G43 is on |
#<_retract_r_plane> | Returns 1 if G98 is set |
#<_retract_old_z> | Returns 1 if G99 is set |
#<_spindle_rpm_mode> | Returns 1 if G97 is on |
#<_spindle_css_mode> | Returns 1 if G96 is on |
#<_ijk_absolute_mode> | Returns 1 if G90.1 is on |
#<_lathe_diameter_mode> | Returns 1 if G7 is on |
#<_lathe_radius_mode> | Returns 1 if G8 is on |
#<_spindle_on> | Returns 1 if the spindle is on |
#<_spindle_cw> | Returns 1 if the spindle is on in the clockwise direction |
#<_mist> | Returns 1 if M7 is on |
#<_flood> | Returns 1 if M8 is on |
#<_speed_override> | |
#<_feed_override> | |
#<_adaptive_feed> | |
#<_feed_hold> | |
#<_feed> | Returns the current active feedrate in the current machine units |
#<_rpm> | Returns the current active RPM |
#<_x> | Returns the current X position, equivalent to parameter #5420 |
#<_y> | Returns the current Y position, equivalent to parameter #5421 |
#<_z> | Returns the current Z position, equivalent to parameter #5422 |
#<_a> | Returns the current A position, equivalent to parameter #5423 |
#<_b> | Returns the current B position, equivalent to parameter #5424 |
#<_c> | Returns the current C position, equivalent to parameter #5425 |
#<_u> | Returns the current U position, equivalent to parameter #5426 |
#<_v> | Returns the current V position, equivalent to parameter #5427 |
#<_w> | Returns the current W position, equivalent to parameter #5428 |
#<_work_offset_x> | |
#<_work_offset_y> | |
#<_work_offset_z> | |
#<_work_offset_a> | |
#<_work_offset_b> | |
#<_work_offset_c> | |
#<_work_offset_u> | |
#<_work_offset_v> | |
#<_work_offset_w> | |
#<_tool_offset_x> | |
#<_tool_offset_y> | |
#<_tool_offset_z> | |
#<_tool_offset_a> | |
#<_tool_offset_b> | |
#<_tool_offset_c> | |
#<_tool_offset_u> | |
#<_tool_offset_v> | |
#<_tool_offset_w> | |
#<_axis_offset_x> | |
#<_axis_offset_y> | |
#<_axis_offset_z> | |
#<_axis_offset_a> | |
#<_axis_offset_b> | |
#<_axis_offset_c> | |
#<_axis_offset_u> | |
#<_axis_offset_v> | |
#<_axis_offset_w> | |
#<_x_machine> | |
#<_y_machine> | |
#<_z_machine> | |
#<_a_machine> | |
#<_b_machine> | |
#<_c_machine> | |
#<_u_machine> | |
#<_v_machine> | |
#<_w_machine> | |
#<_current_tool> | |
#<_current_pocket> | |
#<_value> | |
#<_value_returned> | |
#<_task> | |
#<_call_level> | |
#<_remap_level> | |
#<_probe_result> | Returns the result of a G38 probe result, equivalent to parameter #5070 |
#<_probe_x> | Returns the coordinates of a G38 probe trip, equivalent to parameter #5061 |
#<_probe_y> | Returns the coordinates of a G38 probe trip, equivalent to parameter #5062 |
#<_probe_z> | Returns the coordinates of a G38 probe trip, equivalent to parameter #5063 |
#<_probe_a> | Returns the coordinates of a G38 probe trip, equivalent to parameter #5064 |
Lathe Specific Parameters
When using G10 on the 15L/8L P values of 1-99 will modify the wear offset values.
When using G10 on the 15L/8L P values of 10001-10099 will modify the geometry offset values.