Purpose
This document gives instructions on installing the 1100M+ Servo Upgrade Kit on a mill.
Product Information
Product: 1100M+ Servo Upgrade Kit (PN 39274)
Quantity | Description |
1 | 1100M+ Enclosure Decal (PN 39393) |
1 | 1100M+ Electrical Cabinet Decal (PN 39392) |
3 | 8-Position Terminal Block (PN 32877) |
4 ft | Butyl Tape (PN 34133) |
1 | Cord Grip (PN 38758) |
1 | Cord Grip Nut (PN 30806) |
4 | Cable Gland (PN 35974) |
1 | Dielectric Grease (PN 38268) |
3 | Flex Conduit Fitting (PN 30628) |
4 | M5 × 0.8 - 20 mm Socket Cap Screw (PN 30357) |
4 | M5 Flat Washer (39305) |
4 | M5 Lock Washer (PN 30534) |
1 | M5 Tap (PN 33420) |
1 | M5 Tap Drill (PN 33641) |
1 | X-Axis Servo Control Cable (PN 39398) |
1 | Y-Axis Servo Control Cable (PN 39399) |
1 | Z-Axis Servo Control Cable (PN 39400) |
1 | X-Axis Servo Power Cable (PN 39402) |
1 | Y-Axis Servo Power Cable (PN 39403) |
1 | Z-Axis Servo Power Cable (PN 39404) |
7 | Spade Electrical Connector (PN 30610) |
1 | X-Axis Flex Conduit (PN 30627) |
1 | X-Axis Motor Cover Assembly (PN 39283) |
1 | X-Axis Servo Motor (PN 38404) |
1 | Y-Axis Servo Motor (PN 38701) |
1 | Z-Axis Brake (PN 38399) |
1 | Z-Axis Servo Motor (PN 38405) |
NOTE: If any items are missing, we can help. Create a support ticket with Tormach Technical Support at tormach.com/how-to-submit-a-support-ticket for guidance on how to proceed.
...
Automatic Oiler Required You must confirm that the mill is regularly oiled. If you don't, there's a risk of motor faults. Use an Automatic Oiler Kit: 230 Vac (PN 38255).
Clean Machine Clean all chips and swarf from the machine with a bench brush and a dustpan.
...
ECMv1.5 Update Kit Required If you don't have an ECMv1.5 or later control board, you must first install the ECM1v1.5 Update Kit (PN 39257). For information, see the product's documentation.
Keep All Hardware To install the servo motors, you'll reuse many items currently used on the machine. Keep all hardware unless you're specifically instructed to discard it. If you don't, there's a risk that you won't have the hardware you need to complete the installation.
PathPilot v2.2.X or Later Required Only PathPilot v2.2.X and later has settings required to use a servo motor mill configuration. For information, go to "Update PathPilot".
...
Install an Update File from a USB Drive
| Anchor | ||||
|---|---|---|---|---|
|
From the PathPilot support center, download the most recent PathPilot update file.
Transfer the PathPilot update file to a USB drive.
Put the USB drive into the PathPilot controller.
Confirm that the PathPilot controller is powered on and out of Reset mode.
From the Status tab, select Update.
...
From the PathPilot interface, select Reset.
Confirm that the machine can freely move to the reference position:
Reference the Z-axis before referencing the other axes so that the spindle is clear of any possible obstructions: from the PathPilot interface, select Ref Z.
Once the spindle is clear of any possible obstructions, select Ref X and Ref Y.
Depending on the result of Step 5, do one of the following:
Correct Movement Remove the set of two-by-fours on the machine table, and put back the drip tray that you set aside in "Prepare the Machine".
Incorrect Movement We can help. Create a support ticket with Tormach Technical Support at tormach.com/how-to-submit-a-support-ticket for guidance on how to proceed.
...