Machine Stand - PCNC 440

Purpose

This document gives instructions on assembling the PCNC 440 Stand.

Product Information

Product: PCNC 440 Stand (PN 51497)

NOTE: If any items are missing, we can help. Create a support ticket with Tormach Technical Support at tormach.com/how-to-submit-a-support-ticket for guidance on how to proceed.

Assemble the Machine Stand

You can use thread-locking fluid (not provided) on the screws during the assembly procedure.

1. Before you begin assemby, we recommend that you put a large piece of cardboard (or similar) on the floor to protect the machine stand during certain steps that require access to the bottom of the stand.

2. Find the four legs (PN 51493), the left side panel (PN 51498), and the right side panel (PN 51483). Make note of the following on each component:

   1. Identify the threaded holes in the legs — these are used for the door hinges. When assembled, the threaded holes must be facing forward.

   2. Identify the holes for the upper shelf on the side panels. When assembled, these holes must be toward the top of the stand's legs.

3. Use three M5 × 0.8 - 10 screws (PN 38205) to attach two legs to the left side panel. Repeat this step to attach the remaining two legs to the right side panel.

Open

Figure 1: Attaching the legs to the two side panels.

4. Find the back panel (PN 51484). Use six M5 × 0.8 - 10 screws (PN 38205) to attach it to the two back legs.

Open

Figure 2: Attaching the back panel to the two side panels.

5. Find the bottom shelf (PN 51485). Use four M5 × 0.8 - 10 screws (PN 38205) to attach it to the two side panels.

6. Find the upper shelf (PN 51486). Use eight M5 × 0.8 - 10 screws (PN 38205) to attach it to the two side panels and the back panel.

7. Find the front panel (PN 51487). Use six M5 × 0.8 - 10 screws (PN 38205) to attach it to the two side panels and the bottom shelf.

8. Lay the machine stand onto the cardboard on the floor.

9. Find two bottom stiffeners (PN 51494). Attach them to the bottom of the machine stand as follows:

   1. Use six M5 × 0.8 - 10 screws (PN 38205) to attach one bottom stiffener to the two legs and the back panel of the machine stand.

10. Move the machine stand back upright.

11. Find the four door hinge assemblies (PN 51496), the left door (PN 51488), and the right door (PN 51489). Attach the doors as follows:

    1. Use four M5 × 0.8 - 10 screws (PN 38205) to attach two door hinge assemblies to the left door.

    2. Use four M5 × 0.8 - 10 screws to attach both door hinges to the left side of the front panel.

    3. Repeat Steps A through B to attach the remaining two door hinges to the right door and the right side of the front panel.

12. Find the two door latches (PN 51495). Attach them to each door as follows:

    1. Remove the bracket from the back of the door latch, and temporarily set it aside.

13. Find four top cover blocks (PN 51491), the top cover (PN 51490), and two top cover stiffeners (PN 51492). Assemble the top cover as follows:

    1. Align two of the top cover blocks with the pre-drilled holes on the left side of the top cover.

    2. Align one top cover stiffener to the underside of the top cover.

NOTE: Make sure that the inside of the stiffener faces the middle of the top cover.

NOTE: The center hole in each top cover block is used to mount the machine to the chip pan.

14. Use 12 M5 × 0.8 - 10 screws (PN 38205) to attach the top cover to the stand assembly.

15. Lay the machine stand onto the cardboard on the floor.

16. Find four M12 nuts (PN 35283) and four leveling feet (PN 36034). Attach the feet to the machine stand as follows:

    1. Put one M12 nut on each of the four leveling feet.

    2. Put each leveling foot into each leg as shown in the following image. Make sure that the M12 nut is on the bottom of the leg.

Exploded Views and Parts Lists

Exploded View

Parts List

To view a PDF version of your manual, go to Tormach document TD10809.

If you have additional questions, we can help. Create a support ticket with Tormach Technical Support at tormach.com/how-to-submit-a-support-ticket for guidance on how to proceed.